Gorilla

Gorilla Clear Epoxy Glue

0.85 oz

$6.22 each($7.32 / oz)

Victoria H‑E‑B plus!

6106 N. NAVARRO

Description

Incredibly strong. Sets in 5 min. For the toughest jobs on Planet Earth. Color: Dries clear. Bonded Strength: 3000 PSI. Indoor/Outdoor: Water resistant. Structural gap filler. Bonds: metal, wood, ceramic, glass, most plastic and more! Includes: Resealable cap, stir stick & mixing tray. Incredibly strong and fast setting. Easy, even dispensing. Low odor. Solvent resistant and non-toxic once cured. Made in USA.

Allergens and safety warnings
WARNING: CANCER AND REPRODUCTIVE HARM - WWW.P65WARNINGS.CA.GOV.,FIRST AID TREATMENT: IF SWALLOWED, CALL A POISON CONTROL CENTER OR DOCTOR IMMEDIATELY. DO NOT INDUCE VOMITING. IF IN EYES OR ON SKIN, RINSE WELL WITH WATER. IF ON CLOTHES, REMOVE CLOTHES. IF BREATHED IN, MOVE PERSON INTO FRESH AIR. FOR MEDICAL EMERGENCIES ONLY, CALL 800-420-7186. ,WARNING: HARMFUL IF SWALLOWED. HARM FUL BY SKIN ABSORPTION. EYE, SKIN & RESPIRATORY IRRITANT. WARNING: HARMFUL IF SWALLOWED, HARMFUL BY SKIN ABSORBTION. EYE, SKIN, & RESPIRATORY IRRITANT. MAY PRODUCE ALLERGIC REACTION BY SKIN CONTACT. DO NOT SWALLOW. DO NOT GET IN EYES OR ON SKIN OR CLOTHING. DO NOT BREATHE FUMES. KEEP OUT OF REACH OF CHILDREN. WEAR SAFETY GLASSES AND CHEMICAL RESISTANT GLOVES. WASH HANDS IMMEDIATELY AFTER USE. USE ONLY IN A WELL-VENTILATED AREA. CONTAINS EPOXY RESIN, MERCAPTAN-TERMINATED POLYMER, 1-CHLORO-2,3 EPOXYPROPANE AND AMINE CURING AGENTS. STORE AWAY FROM CHILDREN AND ANIMALS.
DIRECTIONS: IF YOU'RE USING GORILLA EPOXY FOR THE FIRST TIME, OR BONDING A NEW TYPE OF MATERIAL, WE ALWAYS RECOMMEND TRYING A TEST PIECE FIRST. 1. PREPARE YOUR WORK AREA: USE IN A WELL-VENTILATED AREA. BE SURE YOUR WORK AREA IS PROTECTED FROM SPILLS. A MIXING TRAY AND PLASTIC STIR STICK ARE PROVIDED. TO IMPROVE ADHESION, ROUGHEN SMOOTH SURFACES BEFORE GLUING. CLEAN AND DRY ALL SURFACES TO BE BONDED. 2. MIXING GORILLA EPOXY: REMOVE PLASTIC STIR STICK FROM MIDDLE OF PLUNGER. WITH PACKAGE POINTING UPWARD REMOVE THE CLOSURE FROM THE TWO SYRINGES. WITH THE PACKAGE STILL POINTING UPWARD, ELIMINATE AIR AND ENSURE EVEN DISPENSING BY SLOWLY PUSHING THE PLUNGER UNTIL BOTH THE RESIN AND THE HARDENER ARE AT THE TIP. PUSH THE PLUNGER TO DISPENSE EVEN AMOUNTS OF RESIN AND HARDENER ONTO A CLEAN, DISPOSABLE, CONTAINED SURFACE. THE PACKAGE ITSELF CAN BE USED AS A MIXING TRAY. IF YOU FLIP THE PLASTIC BLISTER SHELL OVER, YOU CAN USE THE SMALL WELL AS A STARTER DISH TO BEGIN DISPENSING UNTIL BOTH THE RESIN AND HARDENER ARE FLOWING EQUALLY. ONCE THE FLOW IS EVEN, MOVE TO THE LARGER MIXING WELL TO DISPENSE YOUR EVEN RATIO. USING PLASTIC STIR STICK MIX THE TWO PARTS FOR ABOUT 20 SECONDS, UNTIL THE MIXTURE IS UNIFORM. APPLY WITHIN 5 MINUTES. AS YOU MIX, YOU WILL NOTICE THAT THE EPOXY WARMS UP. THIS IS A REACTION THAT OCCURS AS THE RESIN AND HARDENER COMBINE. 3. APPLICATION: AFTER MIXING IS COMPLETE, APPLY GORILLA EPOXY WITHIN 5 MINUTES. THE EPOXY MIXTURE WILL CONTINUE TO THICKEN, AND THE BOND STRENGTH WILL DECREASE THE LONGER YOU WAIT TO APPLY. 4. CLAMPING: TO REACH MAXIMUM BOND STRENGTH, CLAMP PROJECT TOGETHER AND LEAVE UNDISTURBED. 5. STORAGE: TO CLOSE, SLIGHTLY PULL BACK ON PLUNGER. WIPE TIP CLEAN WITH DRY CLOTH AND ALIGN NOTCH ON TIP AND CAP. CLOSE TIGHTLY. SET TIME: 5 MINUTES TO APPLY AND POSITION. HANDLING TIME: 30 MINUTES UNDISTURBED. CURE TIME: 24 HOURS FOR LOAD BEARING WEIGHT. APPLICATION IN COOLER TEMPERATURES MAY CAUSE LONGER CURE TIMES. TEMP. RANGE: BOND WITHSTANDS -10 DEGREES F TO 180 DEGREES F. CURED COLOR: DRIES CLEAR (HEAT OR SUN EXPOSURE CAN CAUSE PRODUCT TO YELLOW). STORAGE: AFTER USE, CLEAN SYRINGE AND REPLACE CLEAR CAP. STORE IN A COOL, DRY PLACE. CLEAN-UP: REMOVE EXCESS GLUE IMMEDIATELY FROM PROJECT SURFACE WITH DRY CLOTH AND ACETONE, MINERAL SPIRITS OR RUBBING ALCOHOL. SEE BELOW FOR REMOVAL FROM SKIN.